Saturday, November 21, 2026

Garage Works, Part 2 - 11/21/2026

I went ahead and got the top deck laminated this evening.

Almost 0.5 ounces of pigment added to 12 ounces of resin and 4.8 ounces of hardener. 


I didn't want to repeat my mistake of leaving the project while a fluid is transitioning to a solid, so I babysat (drinking and beer) to make sure the laminates did not float or lift while the epoxy hardened.


The laminate came out nice and tight!


I'm still debating what I'm going to do with the bottom deck - either do a full carbon bottom and use clear epoxy to keep it black; or use the carbon patches/strips and repeat what I did for the top deck (cover layer with pigmented fiberglass).

Right now I'm thinking to mirror the top... but I'm going to sleep on it.

Parawing Session - 11/21/2026

The forecast called for strong winds starting around 11am.  I was working in the garage (previous post) through the morning, but broke away to get a session in.

Prayot and I got to the beach and saw a strong north wind cleaning up the surf.  I owed him one more Jollibee trip to pay off the Silk V2 950 - so off we went.

My plan was to eat, go home and take a nap, then come back with a surfboard.

But as we were finishing the food, Roland broadcast there was wind and waves.

Yup - the wind had shifted more east (still a little more north, but workable) and there were a good amount of whitecaps.


Same board and foil - but brought both the BRM S3 5.3 (packed for a come home parawing) and the 4.2 (ready to go).


I used the 4.2 first and there was plenty of wind.  I had a couple of runs to figure out the conditions - but after that, it was big arse wave after big arse wave!!!!

The rides were even better than yesterday!

I probably had 10 big ones before the wind started to throttle back.  I went ahead and switched to the 5.3


And then on one wave I got breached (not sure why - with the AFS UHM 80cm mast I hardly breach) and the leash attachment pulled out.

I had to let go of the parawing for a bit to swim after the board.  It didn't take long and I paddled back to the parawing (which didn't have enough time to sink).  I'm going to try and use the Oceanus reel leash I have and attach it to the NSI pouch.

I also was headed out on a run and a wave started to feather in front of me - I didn't make it over, but I got the parawing to avoid getting eaten. 


You can see the wind from earlier (too light and too north), and the increase in strength once the rain clouds cleared.


I'm getting a better redeploy rate by paying attention to the front edge of the parawing.  Two line take down, gather the ears, tuck the back end of the parawing and ride.  When redeploying, find the front edge and hold on to it while opening the rest of the wing.  Let it gradually open and sail away.

If I don't get the redeploy, it's usually a thinner canopy line that found its way across the thicker lower lines.


Another great WP session!!!!

PF:11/W:3/PW:153/FD:77/S:29

Garage Works - 11/21/2026

I stalled my daily water time to get some extra sleep and then to get this board across the shaping finish line.

I used the planer to get the excess glue off, and even the dremel on the topside, but after that, to fair everything in I used all the shaping hand tools again - rough surform, fine surform, 80 grit sanding screen, and 120 grit sanding screen.

I think the extra time was worth it and I was glad to have been able to salvage the track block. 


The finish is much nicer now and all the imperfections (that I can see) have been leveled out and balanced.


After catching that wave yesterday at the end of the session and riding that parawing board prone, I'm totally energized to get this board completed.


I went ahead and cut out the laminates.

Base layer of carbon covering the block up to where my chest will rest when paddling.  Then a patch forward and aft (just because I had the carbon pieces and I can't be totally sure of where my feet will touch during duck dives and other handling points).

Over that are two strips of carbon tape to act as stringers.

And lastly is a patch of innegra to protect the carbon.


With all this laminate, I'm going to use a single 6 ounce layer of fiberglass to cover everything up.  And yes I'm building this opposite of convention (top deck laminated first) - as I had originally thought about using a carbon bottom (and am still debating that option - and in that case the bottom deck laminate would need to be cut short and covered with rail tape; I can color the top with the laminate coat of epoxy - those decisions still have to be made - I can also just use carbon tape and fiberglass).


I'll likely place the epoxy and fiberglass tonight.

And then looking at how I can make more space in the garage, I saw this mast that Eli gave me so I can set up my tow boogie (converted super short prone board) 


It cut easily with the grinder.    


And here it is with the universal motor pod mount.


Got lots done this morning!  Now its time to parawing!

Garage Works - 11/20/2026

After considering the amount of effort I need to put in to get the incorrectly set block cleaned up, I figured it might be best to reset it in the slot.

And here it is reset.


Since I had it on the ground, it was a good opportunity to look at the rocker - front


And back


I'll get the join areas cleaned up and get this ready for glassing.

I'm thinking carbon patches and fiberglass... (or maybe basalt - but with this planned to be a waxed front foot prone foiling board, basalt really wouldn't have a ton of benefit that an extra patch of fiberglass wouldn't provide - maybe better to save the basalt for a Foil Drive board).

Friday, November 20, 2026

Parawing Session Two - 11/20/2026

And since it was my birthday - I got clearance to get a second session in.

The conditions at White Plains were perfect!

Easterly flow hovering around 20mph - 

Head high swell coming through in sets -

Decent tide on the way out

(AWESOME Birthday present!!!)


I brought the NSI stash pouch and the SeaLine dry bag with the intentions of bringing out two parawings.  But after looking at the whitecaps (and considering the recent patterns) - I opted to just go out with the BRM S3 4.2

Same board and foil - and same mast position (this is good - time to mark it).


La and I had a dinner date set so I did not have unlimited time.  By the time I decided the wind was starting to lose consistency, I was already tired.  I didn't want to make any costly mistakes - but that was an hour and a half in :) 


The retracted rides were incredible!

Probably the same distance covered per ride as Foil Drive -

I was using the center two blue line collapse (comes down easy), and a quick wrap.  My redeploy rate was close to 75%

Kalani came out and was on his 777 Hybrid 4.3 and was ripping like usual.

There were flat spots where the waves would go over the spaces between reef lines - the Silk V2 950 made pumping through those easier.  And when a section stood up - riding was so smooth, no pumping needed at all.


East, strong and steady - perfect!!!


The downs were from me resolving issues with only a few due to lulls.

I stopped my watch - but my last wave was a proper prone ride - paddled in, popped up and rode for quite some distance.  I'm getting excited to be getting back into prone foiling (No.45)


Awesome birthday session!!!

PF:11/W:3/PW:152/FD:77/S:29

Parawing Session - 11/20/2026

Since it was my 55th time around the sun, I got to do two parawing sessions today.

The first was at Hickam - as I wanted to get some tacking in on the AFS Silk V2 950

The wind was on and off, and it would rotate from N to E and back.  Just the kind of conditions that are not good for parawinging.

Stu came with to get the bugs worked out of his new PPC Zen 75l midlength board


I set the mast back to just in front of the Silk V1 1050 setting.  This worked well - making the foil feel more balanced (less front foot pressure, and balanced between both feet).  I also swapped out the USurf 150 for the USurf 135.  That also felt more balanced.


This session was pretty much riding the gusts.  I needed some of the heavier wind to get up on to foil (and figuring out which direction the wind was coming from was half the battle).  But once up, I could stay up in the lighter winds.

But even that faltered when the wind lulled out.

With all the north in the wind, I figured I didn't need the additional drama from trying to head out to Firsts.


I did spend this session mainly figuring out how this foil tacks.  At first I could just get it to go through the tack, but I could foil out of the turn.  By the end of the session I was nailing them.

I also got in a toeside tack - powered and foiled through.


Up and down - with a sizeable lull in the middle of the session.


Lots of correlation -


I really appreciate how little bar pressure the PPC has - makes lots of things possible!

PF:11/W:3/PW:151/FD:77/S:29

Thursday, November 19, 2026

Parawing Session - 11/19/2026

Similar pattern to the past several days - windy with whitecaps early, then the wind backs off once you have paddled out.


But I finally stopped being stubborn and brought two parawings out - the BRM S3 5.3 and 4.2.  The second one stayed in the Camelbak backpack.

No.44 with the AFS UHM 80cm mast, USurf 150 and the new to me Silk V2 950.

I positioned the mast just between the Enduro 900 and Silk V1 1050 marks.


I started with the BRM S3 4.2 and there was enough wind to get up quick.

Retracting is obviously easier with the smaller parawings.  I got some retracted rides, but I got the lines snagged on the backpack straps.  I did get some successful redeploys.

The AFS Silk V2 950 turns nice - a lot like the Silk V1 and even similar to the Domani 960.  It has more glide than the Domani (but maybe less than the Prestige 905).  Less glide than the Enduro 900. 


The wind dropped so I switched out to the S3 5.3

I retracted the 5.3 a lot more than the 4.2 today - just timing and the wind strength.

Long rides with the parawing bunched up - SO MUCH FUN!!!!


There were lots of lulls.

I decided that I'm not going to pumps like mad to get up on to foil - I need to do this to not hurt my shoulders.  The lulls were also good opportunities to rest.


Prayot and Derek came out later on parawing.  Roland came out on wing.


I'm going to target a double session tomorrow!!!

PF:11/W:3/PW:150/FD:77/S:29

Garage Works - 11/19/2026

I got some progress on No.45 - but then took a step back.

I got the shape dialed in first - then I routed out the slot for the track block.


Nice fit -

But I set the block in with Gorilla Glue, set 15 pounds on it, and went in for lunch.


I went back out to check on it thinking the 15 pounds was enough to hold it down.  It wasn't...

The block came up 1/4" - and I couldn't get it back down.

I ended up using a multitool and a Japanese saw to cut the block out before the glue solidified.

Luckily I picked these blocks up...


I got the positioning/measuring completed.


And I even cut the back of the block to fit the cut out.

Tomorrow I'll route out the slot to fit this wider block.  And then I'll place a top block in place.

Honestly I was going to skip the top block, but now that I had to cut out the other block, I guess I'm adding it now... never skip steps - this is really for the better.

And I can still salvage the other block.  I just need to clean it up a bit.

Wednesday, November 18, 2026

Garage Works - 11/18/2026

I did end up taking a rest day - but that doesn't mean I didn't do anything.

I hit the garage and worked on dialing in the final shape of No.45

I used the fine surform and sanding screen.

Here's the bottom deck.


And here is the top deck.


And here is the side profile to show the rocker.


Right now (pre-laminating), the dimensions are:

5'1.5" x 20.5" x 3.375"

Tomorrow I'll route out the slot for the mast track, then glue in the block.

Tuesday, November 17, 2026

Parawing Session - 11/17/2026

The same thing happened to me today as yesterday - the wind was strong when I pulled up to the parking lot and I geared up as such.  Then as I was paddling out, the wind dropped.


I picked up Norm and Stu from PVs so they could do a downwinder.

I used the Cabrinha Prestige 905 with the Tweaker 160 rear stabilizer - I wanted to see what effect the Tweaker setup has compared to the Union monobloc.

For power I used the PPC Orbit 4.5.  I should have used the BRM S3 5.3 based on yesterday's session...


Bottom line up front - this session down right sucked.  The wind was just below the threshold to get up onto foil with the PPC Orbit 4.5


I did get up, so this wasn't a skunk - but this was a hard earned session.

But my runs all ended in a dead wind zone and me coming off foil.

Norm had the same troubles (and eventually cut his heal on his foil, ending his session).  Stu did get up and was having a great time on his new board - PPC Zen at 75 liter.

In trying to get to sufficient wind to jibe and head back in, I did end up dropped twice way outside.  It took a while but I did get back up and didn't have to paddle back.


I think the 5.3 would have been enough -


I may just rest (and work on No.45) tomorrow.  The wind is supposed to be similar to today.  On Thursday it is supposed to ramp up.


Oh - and about the Tweaker fuselage/stabilizer - I did notice a touch more pitch instability, and it seemed a bit harder to pull higher angles upwind - but that may be from the shitty wind.  More testing ahead!!!

PF:11/W:3/PW:149/FD:77/S:29